DIGITAL MIXING ENGINE SATELLITE
Owner’s Manual
EN
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
FCC INFORMATION (U.S.A.)
not guarantee that interference will not occur in all installations. If
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT:When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE:This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reason-
able level of assurance that your use of this product in a residential
environment will not result in harmful interference with other elec-
tronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to elimi-
nate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
(class B)
COMPLIANCE INFORMATION STATEMENT
ADVARSEL!
(DECLARATION OF CONFORMITY PROCEDURE)
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskift-
ning må kun ske med batteri af samme fabrikat og type. Levér det
brugte batteri tilbage til leverandoren.
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif.
90620
Telephone : 714-522-9011
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp
eller en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.
Type of Equipment : DIGITAL MIXING ENGINE SATELLITE
Model Name : DME8i-C/DME8o-C/DME4io-C
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda
paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä
käytetty paristo valmistajan ohjeiden mukaisesti.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including inter-
ference that may cause undesired operation.
(lithium caution)
See user manual instructions if interference to radio reception is sus-
pected.
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
(FCC DoC)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
NEDERLAND / THE NETHERLANDS
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED
IMPORTANT. The wires in this mains lead are coloured in accor-
dance with the following code:
• Dit apparaat bevat een lithium batterij voor geheugen back-up.
• This apparatus contains a lithium battery for memory back-up.
• Raadpleeg uw leverancier over de verwijdering van de batterij op
het moment dat u het apparaat ann het einde van de levensduur of
gelieve dan contact op te nemen met de vertegenwoordiging van
Yamaha in uw land.
GREEN-AND-YELLOW
BLUE
BROWN
:
:
:
EARTH
NEUTRAL
LIVE
• For the removal of the battery at the moment of the disposal at the
end of life please consult your retailer or Yamaha representative
office in your country.
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals
in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be con-
nected to the terminal in the plug which is marked by the letter E or
• Gooi de batterij niet weg, maar lever hem in als KCA.
• Do not throw away the battery. Instead, hand it in as small chemical
waste.
by the safety earth symbol
YELLOW.
or colored GREEN or GREEN-and-
The wire which is coloured BLUE must be connected to the termi-
nal which is marked with the letter N or coloured BLACK.
(lithium disposal)
The wire which is coloured BROWN must be connected to the ter-
minal which is marked with the letter L or coloured RED.
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.(3 wires)
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/Power cord
Water warning
• Only use the voltage specified as correct for the device. The required voltage is
printed on the name plate of the device.
• Do not expose the device to rain, use it near water or in damp or wet conditions,
or place containers on it containing liquids which might spill into any openings.
• Use only the included power cord. If you intend to use the device in an area
other than in the one you purchased, the included power cord may not be
compatible. Please check with your Yamaha dealer.
• Never insert or remove an electric plug with wet hands.
If you notice any abnormality
• Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.
• If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the device, or if any unusual smells or smoke
should appear to be caused by it, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the device inspected by
qualified Yamaha service personnel.
• Be sure to connect to an appropriate outlet with a protective grounding
connection. Improper grounding can result in electrical shock.
• If this device should be dropped or damaged, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the device
inspected by qualified Yamaha service personnel.
Do not open
• Do not open the device or attempt to disassemble the internal parts or modify
them in any way. The device contains no user-serviceable parts. If it should
appear to be malfunctioning, discontinue use immediately and have it inspected
by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord
Inadequate ventilation can result in overheating, possibly causing damage to the
device(s), or even fire.
• Remove the electric plug from the outlet when the device is not to be used for
extended periods of time, or during electrical storms.
• If several of the devices are mounted in an EIA-compliant rack, carefully read the
• When removing the electric plug from the device or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
• Avoid setting all equalizer controls and faders to their maximum. Depending on
the condition of the connected devices, doing so may cause feedback and may
damage the speakers.
Location
• Do not expose the device to excessive dust or vibrations, or extreme cold or heat
(such as in direct sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration or damage to the internal components.
• Before moving the device, remove all connected cables.
• When setting up the product, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn off
the power switch and disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product at the minimum
level. When you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
• Do not place the device in an unstable position where it might accidentally fall
over.
• Do not block the vents. This device has ventilation holes at the rear to prevent
the internal temperature from becoming too high. In particular, do not place the
device on its side or upside down. Inadequate ventilation can result in
overheating, possibly causing damage to the device(s), or even fire.
• If this device is to be mounted in an EIA-standard rack, leave the back of the rack
open and make sure that it is at least 10 cm away from walls or surfaces. Also, if
this device is to be mounted with devices that tend to generate heat, such as
power amplifiers, be sure to keep an adequate gap between this device and the
heat-generating devices or install ventilation panels to prevent high
temperatures from developing inside this device.
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Doing so may result in noise, both in the device
itself and in the TV or radio next to it.
(5)-4 1/2
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
4
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connections
Backup battery
• Before connecting the device to other devices, turn off the power for all devices.
Before turning the power on or off for all devices, set all volume levels to
minimum.
• This device has a built-in backup battery. When you unplug the power cord from
the AC outlet, the current scene data is retained. However, the life of the backup
battery is about five years. If the battery wears out, the current scene data will be
lost. When the backup battery charge becomes low, the [ERROR] indicator on
the front panel blinks. In this case, save the data to a computer immediately,
then ask a Yamaha dealer to replace the backup battery.
Handling caution
• Do not insert your fingers or hands in any gaps or openings on the device.
• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any
gaps or openings on the device. If this happens, turn off the power immediately
and unplug the power cord from the AC outlet. Then have the device inspected
by qualified Yamaha service personnel.
• Do not use the device for a long period of time at a high or uncomfortable
volume level, since this can cause permanent hearing loss. If you experience
any hearing loss or ringing in the ears, consult a physician.
• Do not rest your weight on the device or place heavy objects on it, and avoid use
excessive force on the buttons, switches or connectors.
Do not turn the [POWER] switch on and off repeatedly and rapidly. Be sure to wait six seconds or more between turning the power to the unit off and then on.
The rubber feet included in this package can be attached to the bottom of this device to prevent slippage when it is to be used on a slippery surface.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
Always turn the power off when the device is not in use.
The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualified Yamaha service
personnel about replacing defective components.
• The illustrations in this owner’s manual are for instructional purposes, and may appear somewhat different from the actual equipment.
• CobraNet is a trademark of Cirrus Logic, Inc.
• Ethernet is a trademark of Xerox Corporation.
• All other trademarks are the property of their respective holders and are hereby acknowledged.
(5)-4 2/2
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
5
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Contents
Accessories (Please make sure the following items are
Controlling external head amplifiers from
Controlling a DME Satellite’s internal head amps from
Controlling DME Satellite’s internal head amps from
Controlling the DME Satellite from a digital mixer
Differences between DME8i-C, DME8o-C,
1. MIDI functions on the DME8i-C, DME8o-C,
Rear Panel..................................................................... 20
[NETWORK] Connector (100Base-TX Ethernet,
Analog Audio Connection ([INPUT] & [OUTPUT]
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
6
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Foreword
Thank you for choosing a Yamaha DME8i-C/DME8o-C/DME4io-C Digital Mixing Engine Satellite.
In order to take full advantage of the features and performance provided by the DME8i-C/DME8o-C/DME4io-C, we urge you
to read this owner’s manual thoroughly before connecting or using the unit. Keep this manual in a safe place for future reference.
Accessories (Please make
sure the following items are
included in the package.)
Preparation
Connecting the AC power cord
•
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
(this document)
Be sure to turn all devices OFF before connecting AC
mains power.
•
•
•
•
AC power cord
CAUTION
Euroblock plug (16P) x 1
Euroblock plug (3P) x 8
Rubber feet x 4
First plug the female-connector end of the AC cord into the
[AC IN] socket on the rear panel of the DME Satellite, then
plug the male plug into an appropriate AC mains outlet.
Be sure to use the voltage specified for the device.
Options
Control Panels
Turning the power on and off
•
•
•
•
ICP1 Intelligent Control Panel
CP4SW Control Panel
CP4SF Control Panel
CP1SF Control Panel
To prevent the initial power-on surge from generating a
large noise spike or damaging your speaker system, turn
the devices on in the following order: audio sources, mixer
(such as M7CL or PM5D), DME Satellite, and finally
CAUTION
power amplifiers.
Reverse this order when turning power off.
NOTE
For more information on your Control Panel, refer to the owner’s
manual that came with the Control Panel, as well as the DME
Designer Owner’s Manual.
1. Press the [POWER] switch to turn on the
power to the DME Satellite.
2. Press the [POWER] switch again to turn off
the power.
About the Product Names
In this manual, models DME8i-C, DME8o-C, and
DME4io-C are all called “DME Satellite,” and models
DME64N and DME24N, DME8i-ES/DME8o-ES/
DME4io-ES and the DME Satellite are categorized as the
DME series.
NOTE
The DME Satellite remembers scene settings when you turn off
the power.
When you turn on the power to the DME Satellite, it will start up
with the same scene settings.
You can use the “Last Mem. Resume” setting in DME Designer
to set up the DME Satellite so that at the startup it will recall the
scene selected before you turned off the power to the device.
About the Firmware Version
You can check the version number of the DME Satellite
firmware by using the DME Designer application software.
• Do NOT turn off the power to the DME Satellite while
it is receiving data from DME Designer or while it is
being manipulated from an external device. Otherwise,
a malfunction may occur.
• Even when the power switch is turned off, electricity is
still flowing to the product all the minimum level.
You can also download the latest firmware from the follow-
ing Yamaha website.
CAUTION
When you are not using the product for a long time,
make sure to unplug the power cord from the wall AC
outlet.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
7
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Foreword
Precautions for Using a
Rack-mounted DME Satellite
If several DME Satellite units (or a DME Satellite unit to-
gether with other devices) are installed in a poorly-ventilated
rack, the heat generated by each unit may raise the tempera-
ture inside the rack, preventing the DME Satellite from per-
forming as designed. When mounting DME Satellite units
in a rack, please leave one rack space vacant for every two
units. You can attach a ventilation panel to this space or leave
it open to prevent excessive heat build-up.
If the temperature inside the rack is expected to rise above 40
degrees Celsius or 104 degrees Fahrenheit (or if the ambient
temperature outside the rack is expected to rise above 30 de-
grees Celsius or 86 Fahrenheit), install a fan kit in the top
3
row of the rack. The fan must provide airflow of 1.6m /min
or more and static pressure of 5mmH O or more.
2
Fan kit
INPUT
PEA
K
PEA
K
PEA
K
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEA
K
SIGNAL
SIGNAL
SIGNAL
DME Satellite
DME Satellite
INPUT
INPUT
PEA
K
PEA
K
PEA
K
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEA
K
SIGNAL
SIGNAL
SIGNAL
INPUT
Ventilation panel
DME Satellite
DME Satellite
INPUT
PEA
K
PEA
K
PEA
K
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEA
K
SIGNAL
SIGNAL
SIGNAL
INPUT
INPUT
PEA
K
PEA
K
PEA
K
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEA
K
SIGNAL
SIGNAL
SIGNAL
INPUT
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
8
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
Differences between DME8i-C, DME8o-C, and DME4io-C
The differences between these three models are as follows:
■ DME8i-C
This model features 8-channel analog inputs.
■ DME8o-C
This model features 8-channel analog outputs.
■ DME4io-C
This model features 4-channel analog inputs and 4-channel analog outputs.
DME Satellite Features
In addition to basic mixing and matrix output functions, the DME Satellite includes a equalizers, compressors,
delay, etc. – that can be patched together via DME Designer to configure just about any audio system you need.
The CobraNet connectors on the device enable you to remotely control analog inputs and outputs by transferring
digital audio signals via a network.
The following steps summarize the process for setting up the DME Satellite for use:
(For details, refer to the “DME Setup Manual”.)
1. Install USB-MIDI Driver, DME Designer and DME-N Network Driver.
3. Connect devices.
• Network connection
• External device connection
4. Make network settings on your computer.
5. Create a configuration using DME Designer, then transfer it to the DME Satellite.
(Refer to the DME Designer Owner’s Manual for details.)
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
9
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
Audio System Network
Multiple DME series units that are interconnected in a network via Ethernet function as a single audio system.
In a DME audio system, a group of the same models that can be operated in sync is called a “device group;” audio
processing divisions that accommodate multiple device groups are called “zones;” and the entire area serviced by
the acoustic system is called an “area.”
Each device group always includes one DME series unit that functions as the “group master” and controls all other
DME series units in the same device group.
If a computer is connected to the network, you can use the computer to control an entire device group via the
group master.
Glossary for the DME Satellite
This section explains terminology specific to the DME Satellite.
Components and parameters
The individual audio processing modules (equalizers, compressors, etc.) are called “components.”
External head amplifier control modules are also available as components.
Changing the parameters of components enables control over the operation of the components.
Configuration
A “configuration” is a complete set of components for constructing an audio system.
Each configuration determines the audio function(s) of the corresponding DME Satellite unit.
All parameter sets included with each component in a configuration are called “preset parameters.”
One DME Satellite unit has a number of configurations, and a configuration has a number of preset parameters.
User Defined buttons (User Defined parameters)
Assigning parameters to be User Defined parameters enables you to control the device from the ICP1 and the
DME64N/DME24N.
Refer to the DME Designer Owner’s Manual for details.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
10
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
Scene
A combination of all configuration and preset parameters is called a “scene.”
Scenes can be recalled from an ICP1, GPI device, other external controllers, DME64N/DME24N, or computer.
Up to 999 scenes can be stored for each device group.
Scene structure
Preset
Parameter
Scene
Scene 1
Scene 2
Configuration
Matrix Mixer
Ex.: Gate
• Attack
• Decay
• Range
• Threshold
• Key in
• Hold
16 x 8
Scene 999
Component
Scene change
First Act
Dark Change
Second Act
Band Set
Play Set
Band
Set
Play Set
Play
Set
Band Set
Stage
Stage
Stage
INPUT
PE
SIGNAL
INPUT
PE
SIGNAL
PE
A
K
A
K
PE
A
K
PE
A
K
A
K
PE
AK
DIGITAL MIXING ENGINE SATELLITE
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
SIGNAL
USB
USB
PEA
K
PEA
K
PEA
K
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
INPUT
INPUT
Scene 1
Scene Recall
Scene 2
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
11
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
Signal Types
DME Satellite audio system signals can be broadly categorized as follows.
Audio
1
Analog and digital signals are input and output between the DME Satellite, other DME series units, and other
audio devices.
Analog signals are input and output via the [INPUT]/[OUTPUT] jacks. Digital signals are input and output via
the CobraNet jacks.
Device group control
Device group control signals control all DME series devices in the group.
2
There are two types of device group control signals, as follows:
•
•
Control signals between the computer and the group master DME series unit
Control signals between the group master DME series unit and the other DME series
units
You can use the DME Designer application to control the entire device group, such as sending components to the
devices and setting the parameters as required.
Device control
These signals provide communication and control between individual devices.
3
Included in this category are MIDI messages transferred between [USB] connectors, GPI signals transferred be-
tween [GPI] connectors, and remote head amp control signals handled via the [REMOTE] connector.
Type of signals handled by the DME Satellite
Reference
Page
Connector
Audio Signal
Device Control
• Control signals between computer and DME
Satellite
[USB] Connector
—
• MIDI messages
• Control signals between computer and DME
Satellite
• Control signals between DME Satellites
• Control signals with a controller such as an
AMX or Crestron
[NETWORK] Connector
—
• Internal head amp control signals with a digital
mixer
• Control signals between PM5D and DME
Satellite.
Up to 16 channels of input
and output.
CobraNet Connector
[GPI] Connector
GPI control signals between GPI device (GPI
controller, etc.) and DME series unit
—
—
• Control signals to/from an external device
(such as AD8HR head amplifier)
• Control signals for a digital mixer and internal
head amp
• Control signals with a controller such as an
AMX or Crestron
[REMOTE] Connector
• MIDI messages
[INPUT]/[OUTPUT]
Connectors (audio in/out)
The number of I/O channels
depends on model.
—
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
12
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
System Examples
Multiple DME Satellite units: Large-scale system
Space B
Space A
DME8i-C
INPUT
PE
SIGNAL
Computer
PE
A
K
A
K
PE
AK
ICP1
DIGITAL MIXING ENGINE SATELLITE
DIGITAL MIXING ENGINE SATELLITE
DIGITAL MIXING ENGINE SATELLITE
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
Analog In
DME8i-C
INPUT
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
Hub
Hub
Analog In
Analog In
Analog In
DME8i-C
INPUT
PE
A
K
PEA
K
PE
AK
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
Hub
DME8i-C
INPUT
PE
A
K
PEA
K
PE
AK
SIGNAL
SIGNAL
SIGNAL
USB
PE
A
K
PE
A
K
PE
AK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME64N
SCENE
HOME
UTILITY
LEVEL
MUTE
CANCEL
ENTER
Space C
MY16-CII × 3
DME8o-C
DME8o-C
Analog Out
Analog Out
Hub
Hub
Hub
DME8o-C
DME8o-C
Analog Out
Analog Out
Space D
DME8i-C
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PE
A
K
PE
A
K
PE
AK
Ethernet
SIGNAL
SIGNAL
SIGNAL
INPUT
CobraNet
Analog In
Ethernet Switching Hub
CobraNet Switching Hub
DME4io-C
Analog Out
Hub
Hub
Analog In
Analog Out
DME8o-C
DME4io-C
Analog Out
Analog In
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
13
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
About DME Designer
DME Designer software enables you to integrate, configure, and control the DME series system from a connected
computer.
You can build the DME series audio system using graphic blocks in DME Designer that are displayed on the com-
puter monitor.
The DME series settings, configuration, and parameter data are transferred from the computer to the DME series
unit via the USB or Ethernet connection.
DME series settings, configuration, and parameter data is sent via USB or Ethernet to the connected DME series
unit. After the data is transmitted, you can disconnect the DME series unit from the computer and use it as an
independent processor.
You can also connect it to a computer and control it in realtime from DME Designer.
If multiple DME series units are connected in the network, DME Designer enables you to build a configuration
that includes those units.
Please download the DME Designer application, driver, DME setup manual, and DME Designer owner’s manual
at the following URL:
Satellite. For details on how to install DME Designer and the drivers that are required for connection, refer to the
“DME Setup Manual”.
Refer to the DME Designer Owner’s Manual for setup and operation instructions.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
14
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
About CobraNet
CobraNet in a nutshell
Developed by Cirrus Logic, Inc., U.S., CobraNet technology allows real-time uncompressed digital audio distri-
bution over industry-standard Fast Ethernet (100 megabits/sec.) networks.
Up to 128 channels, 64 in each direction, can be carried simultaneously over a CobraNet network.
(The number of channels available depends on the performance of the devices and the condition of audio signals.)
CobraNet currently supports a 48 or 96 kHz sampling rate with 16, 20, or 24-bit resolution.
It can also transfer control data along with audio signals.
The type of control data that the network can handle depends on the type of devices on the network.
When an audio signal passes through the CobraNet network, it causes a fixed latency of 5.33 milliseconds (or,
depending on the setting, 2.67 or 1.33 milliseconds).
Visit the CobraNet home page for more information on CobraNet.
CobraNet home page
Bundle
CobraNet network transmits digital audio data in bundles. When bundles are received, they are converted back
into the original digital audio data.
With the DME Satellite, a single bundle can carry up to eight channels of digital audio.
For routing around the network, bundles are assigned numbers from 1 through 65,279. If you set the same bundle
number on both transmitting and receiving devices, digital audio data can be transmitted over CobraNet network.
There is no limitation to the number of bundles that can be transmitted and received over the CobraNet network,
as long as there are enough network resources.
The number of bundles that can be handled depends on the device.
The DME Satellite can use up to 4 output bundles and up to 8 input bundles.
You can specify the bundle number by using the DME Designer application.
The maximum number of channels that can be assigned to each bundle is as follows.
Maximum channels per bundle
Latency
5.33ms
2.67ms
1.33ms
16bit, 48kHz
20bit, 48kHz
24bit, 48kHz
16bit, 96kHz
20bit, 96kHz
24bit, 96kHz
8
8
8
8
8
8
7
8
8
4*
4*
4*
4*
4*
4*
3**
4*
4*
*
Since 96-kHz audio is handled as two 48-kHz signals combined, the maximum number of channels is halved.
** The audio signal output from the 4th channel will include some aliasing noise, and proper operation cannot be guaranteed.
Please do not use this channel.
NOTE
The number of channels per bundled can be changes as shown below.
Depending on the configuration, the maximum number of channels that can be handle may be less than 8.
Number of bundles per channel and usable channels
Bundle
1
Bundle
2
Bundle
3
Bundle
4
Bundle
5
Bundle
6
Bundle
7
Bundle
8
Channels per Bundle
8
4
2
1
1-8
1–4
1–2
1
9-16
5–8
3–4
2
–
9–12
5–6
3
–
13–16
7–8
4
–
–
–
–
–
–
11–12
6
–
13–14
7
–
15–16
8
9–10
5
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
15
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
Multicast and unicast bundles
CobraNet bundles can be either multicast or unicast.
Multicast bundles are transmitted from one device to multiple devices on the network (one-to-many). Unicast
bundles are transmitted from one device to another (one-to-one).
Unicast bundles are transmitted only when another device is configured to receive them by assigning the same
bundle numbers. On the other hand, multicast bundles are transmitted to all devices on the network regardless of
whether any devices are configured to receive them, and only devices that are configured to receive those bundles
actually process them.
It is recommended that no more than four multicast bundles (offering up to 32 channels) be used, since transmis-
sion of multicast bundles consumes more network resources.
Unicast bundles should be used if five or more bundles are required. It is also possible to set multiple devices to
receive the same unicast bundle number, and depending on the transmitting device up to 4 receiving devices may
be able to simultaneously receive the same bundle. This situation is known as “multi-unicast.” The DME Satellite
is capable of handling multi-unicast bundles.
Multicast and unicast bundles are identified by bundle number. Multicast bundles are numbered 1 through 255.
Unicast bundles are numbered 256 through 65,279.
Multicast bundle
CobraNet Device
A
CobraNet Device
B
Digital Audio Data
If Device A is transmitting multicast
bundles, they will be transmitted to
all devices on the CobraNet net-
work (e.g., Devices B, C, and D in
the example).
Network
C
D
CobraNet Device
CobraNet Device
Unicast bundle
CobraNet Device
A
CobraNet Device
B
Digital Audio Data
If Device A is transmitting unicast
bundles, and the same bundle num-
bers are assigned to the transmitting
bundles on Device A and receiving
bundles on Device D, then Device
A will transmit the unicast bundels
to Device D.
Network
C
D
CobraNet Device
CobraNet Device
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
16
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Introduction to the DME Satellite
Conductors and performers
One device on the CobraNet network works as the conductor (network sync master). All other CobraNet devices
are performers (network sync slaves). Each device synchronizes its own internal clock to the beat packets (sync
signals) transmitted by the conductor.
The conductor device is chosen automatically and no user intervention is required.
However, setting an appropriate conductor priority could enable users to assign any device as the conductor.
Refer to the DME Designer Owner’s Manual for more information on setting the conductor priority.
If the DME Satellite is the conductor, the [IN USE/CONDUCTOR] LED flashes orange.
If the conductor fails, another device automatically takes over.
Since the conductor transmits beat packets (sync signals) onto the network, each performer does not require an
external word clock connection, reducing cabling complexity and cost.
Any non-networked digital audio equipment should derive its word clock from a CobraNet networked device.
NOTE
All CobraNet networked devices, regardless of whether each device serves as the conductor or a performer, can receive digital
audio data and control data.
Cables and hubs for CobraNet network
Category-5 metal cables can be used for runs of up to 100 meters. The maximum distance for multimode fiber
optic cable is 2 kilometers.
However, due to differences in cables, as well as switching hub and CobraNet device performance, proper opera-
tion at the maximum length cannot be guaranteed in all cases.
Always use switching hubs in a CobraNet network. When using metal cable for connections, be sure to use Cat-
egory 5 straight cables.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
17
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Controls and Connectors
Front Panel
2 5
7
9
9
9
DME8i-C
INPUT
PEAK
PEAK
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
1
3 4 6
8
2 5
7
DME8o-C
PEAK
PEAK
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
1
3 4 6
8
2 5
7
DME4io-C
INPUT
PEAK
PEAK
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
1
3 4 6
8
1 [USB] Connector
• Before you connect the DME Satellite to the computer
via USB, cancel the computer’s energy saving mode
(such as Suspend, Sleep, or Stand-by mode).
Use this connector to connect the DME Satellite to the com-
puter’s USB port. If you plan to use a USB connection, you
must first install the USB-MIDI Driver on your computer.
• Before turning on the power to the DME Satellite, first
connect its [USB] connector to the computer’s USB
port.
Refer to the “DME Setup Manual” (PDF file) for installa-
tion instructions.
• Before turning the power to the unit on or off, and
before connecting or disconnecting the USB cable, take
the following actions:
- Quit all open applications.
- Make sure that the DME Satellite is NOT transferring
any data.
Be sure to follow the procedure below when you make a USB
connection with a computer. Otherwise, the computer and/
or DME Satellite may freeze, resulting in damages or loss of
data.
CAUTION
If the computer or DME Satellite freezes, turn the power to
the DME Satellite off and then on, then restart the comput-
er.
• Be sure to wait six seconds or more between turning the
power to the unit on and then off (or off and then on),
or between connecting and disconnecting (or vice versa)
the USB cable.
2 [NETWORK] Indicator
Lights orange while data communication is occurring via the
[USB] or [NETWORK] connector.
3 [MASTER] Indicator
Lights green when the device is operating as the group mas-
ter. The indicator is turned off if the device is operating as a
slave.
You can assign the group master in DME Designer.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
18
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Controls and Connectors
4 [ERROR] Indicator
Caution when turning the
power off
Lights when an error occurs. The [PEAK] indicators reflect
the type of error. The [ERROR] indicator flashes when the
battery charge is getting low.
Do not turn off the power while the front panel
[SIGNAL] indicators are lighting consecutively in
the clockwise direction.
5 [IN USE/CONDUCTOR] Indicator
Lights orange when the power is supplied correctly to the
DME Satellite. It flashes while the device is operating as a
CobraNet conductor. If the secondary (backup) connector
turns off every three seconds to indicate an abnormality on
the primary connection.
Lights consecutively in
the clockwise direction
NOTE
connectors.
This indicates that data is being written into internal mem-
ory, and part of the data may be damaged if you turn off the
power at this time. Data writing will occur during the fol-
lowing operations.
6 [LINK/ACTIVITY] Indicator
Lights up steadily or flashes slowly when cables are connect-
ed correctly to the CobraNet connectors. It flashes rapidly
while the unit is transferring data onto the network correctly.
If the secondary (backup) connection is being used for com-
munication, the indicator turns off every three seconds to in-
dicate an abnormality on the primary connection.
• While shifting to on-line operation
• While storing or deleting scene memory
• While saving changes to the Utility settings
• While using the DME File Storage function to transmit/
receive or delete files
• While updating the firmware, or while reverting to the
previous firmware following a failed update
7 [PEAK] Indicators
Light red when the signal level at the corresponding built-in
analog audio inputs or outputs ([INPUT] or [OUTPUT]
connectors) reaches or exceeds -3 dBFS. They also indicate
an error number or status.
8 [SIGNAL] Indicators
Light green when the signal level at the corresponding built-
in analog audio inputs or outputs ([INPUT] or [OUTPUT]
connectors) reaches or exceeds -40 dBFS. They also indicate
the status, for example, of the initialization process.
NOTE
Remove the transparent protective film that was applied to the
indicator panel prior to shipment from the factory.
9 [POWER] Switch
Turns mains power to the device on and off. The DME Sat-
ellite will start up with the same scene settings that were active
when it shut down. You can use the “Last Mem. Resume” set-
ting in DME Designer to set up the DME Satellite so that at
startup it will recall the scene selected before you turned off
the power to the device.
• If “Last Mem. Resume” is set to ON, the unit will back
up data to the internal memory periodically. In this
case, do not turn off the power to the unit within five
CAUTION
(5) seconds after you operate any parameters.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
19
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Controls and Connectors
Rear Panel
1
3
4
5
6
7
9
DME8i-C
MAC ADD
*
XX XX XX XX XX XX *
RS-232C
RS-422
2
8
1
3
4
5
6
7
DME8o-C
MAC ADD
*
XX XX XX XX XX XX *
RS-232C
RS-422
2
8
)
9
1
3
4
5
6
7
DME4io-C
MAC ADD
*
XX XX XX XX XX XX
*
RS-232C
RS-422
2
)
8
1 [AC IN] Connector
NOTE
Connect to the AC mains using the supplied AC power cord.
Use a STP (Shielded Twisted Pair) cable for this connection to
prevent electromagnetic interference.
First connect the power cord to the DME Satellite, then in-
sert the power cord plug into an AC outlet.
4 Dip Switch
Even when the power switch is turned off,
electricity is still flowing to the product all the
minimum level. When you are not using the
This 6-bit dip switch enables you to select the [REMOTE]
connector function or initialize the DME Satellite, depend-
ing on its setting at the startup of the device. To switch be-
tween RS-232C and RS-422 for the [REMOTE] connector
function, turn off the power to the device, set the dip switch
as shown below, then turn on the power to the device again.
CAUTION
product for a long time, make sure to unplug the
power cord from the wall AC outlet.
2 Ground Screw
For maximum safety be sure to securely connect the DME
Satellite ground screw to an earth connection. The supplied
power cable has a three-prong plug that will ground the unit
when the plug is inserted into an appropriately grounded
three-prong type AC mains outlet. If the AC outlet is not
grounded, be sure to ground the unit by using this ground
screw. Correct grounding will effectively eliminate hum
noise and interference.
RS-232C
RS-422
RS-232C
RS-232C
RS-422
RS-422
If you do not plan to initialize the DME Satellite,
set all dip switch bits (excluding one bit for the
RS-422 setting) in the upper position.
CAUTION
3 [NETWORK] Connector
This is a 100Base-TX/10Base-T Ethernet connector for con-
nection to a computer or to another DME series unit in the
5 [REMOTE] Connector
This 9-pin D-SUB connector allows connection to a Yama-
ha AD824 or AD8HR remote head amplifier or an RS-
232C/RS-422 compatible controller such as those from
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
20
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Controls and Connectors
6 CobraNet [PRIMARY]/[SECONDARY]
Connectors
The DME Satellite features two CobraNet connectors for
built-in redundancy: one for a primary network connection,
another for a secondary or backup connection. If for some
reason the primary connection fails (e.g., a cable is damaged,
inadvertently disconnected, or a switching hub fails), the sec-
ondary connection automatically kicks in. Audio transmis-
sion is momentarily interrupted, but the duration of
interruption varies depending on the hub performance or
settings, and the system configuration.
NOTE
• You can check the CobraNet connection status by looking at
the [IN USE/CONDUCTOR] and [LINK ACTIVITY]
indicators. The indicators on both sides to the CobraNet
connectors are turned off.
• Use a STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference.
7 MAC Address
This is the CobraNet’s MAC (Media Access Control) ad-
dress.
8 [GPI] Connector
This Euroblock connector provides access to the unit’s GPI
(General Purpose Interface) interface for transfer of control
signals to and from external equipment. It features 8-port in-
put and 4-port output. The +V terminals have an output
voltage of 5 volts. The IN terminal detects voltage changes
from 0V to 5V. The OUT terminals output either signal “L”
9 [INPUT] Connectors
These Euroblock connectors receive 8-channel analog audio
signals on the DME8i-C.
These Euroblock connectors receive 4-channel analog audio
signals on the DME4io-C.
NOTE
• The PAD will be internally switched on or off when the gain of
the DME8i-C/DME4io-C internal head amp is adjusted
between –6 dB and –5 dB. Keep in mind that noise may be
generated if there is a difference between the Hot and Cold
output impedance of the external device connected to the
INPUT connector when using phantom power.
) [OUTPUT] Connectors
These Euroblock connectors output 8-channel analog audio
signals on the DME8o-C.
These Euroblock connectors output 4-channel analog audio
signals on the DME4io-C.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
21
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to a Computer
USB Connection
To connect multiple DME Satellite units to a network, you must assign appropriate IP addresses and make other
network settings on all units. To achieve this, you need to connect the [USB] connector of one of the DME Sat-
ellite units to the USB port of the computer using USB cables, install USB-MIDI Driver and DME Designer on
the computer, then assign the IP addresses to the DME Satellite units from DME Designer.
NOTE
• Refer to the “DME Setup Manual” (PDF file) for details on installing USB-MIDI Driver and DME Designer.
• Make sure that the USB-MIDI Driver’s THRU setting is “OFF.”
• Refer to “Network Settings” on page 23 for more information on assigning IP addresses from DME Designer.
USB connections can be used in the following three ways:
(1) Set up the network (e.g., assign a unique IP address to each DME Satellite) from DME Designer.
(2) Control the DME Satellite from DME Designer.
(3) Connect to any individual DME Satellite and control that DME Satellite unit by transmitting MIDI com-
mands from a MIDI sequencer or similar software.
NOTE
• When using a DME Satellite together with the DME64N/24N, you must assign the DME Satellite (including the DME8i-
ES/DME8o-ES/DME4io-ES) as the master.
• The computer on which DME Designer is running can be connected to either the group master or a slave DME series unit.
• The correspondence between the MIDI commands to be received/transmitted and the scene parameters can be set up using
DME Designer.
• The USB port being used by DME Designer is not available for use by a MIDI sequencer or other application.
USB Cable
Device Group
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
Ethernet Cable
Computer
(Running DME Designer.)
Switching Hub
Ethernet
Straight Cable
Ethernet Cable
DME64N/24N
INPUT
PE
SIGNAL
PE
A
K
A
K
PE
AK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
SCENE
HOME
UTILITY
LEVEL
MUTE
CANCEL
ENTER
DME Satellite
Computer
(Running MIDI
Sequencer or
USB Cable
similar application.)
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
22
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to a Computer
Network Settings
Use DME Designer to specify the IP address, master/slave, and master ID settings as follows.
Setting the IP address
Network Address
Host Address
Each group of digits between periods in an IP address is called an “octet.” These groups of digits are called “1st
octet,” “2nd octet,” etc., starting from the left-most digit group.
You cannot specify 0, 127, or 223 through 255 for the 1st octet of the network address.
You can specify the following range of values for the 4th octet.
Master : 2-253
Slave : 3-253
NOTE
• Subnet mask is fixed at 255.255.255.0.
• The network address of Gateway is the same as that of IP address. The host address of Gateway is automatically set to 254.
• Assign each of DME series units a unique IP address so that there are no duplicates. Assigning duplicate IP addresses may
cause serious network problems.
• You cannot make any network settings while using the DME Designer application on-line. To make network settings, first
set DME Designer off-line. Refer to the DME Designer Owner’s Manual for details.
• If you have connected a PM5D and a DME Satellite via CobraNet and are controlling the DME Satellite from the PM5D,
you must specify a value of 2 as the fourth octet of the group master DME Satellite’s IP address. However, if the PM5D is
version 2.20 or higher and the DME Satellite is version 3.07 or higher, you can set the parameter to any number.
Master and slave setting
Each device group must have one master. All other devices in the group are assigned as slave.
The fourth octet of a slave DME Satellite’s master ID must be the same value as the fourth octet of the group
master DME Satellite’s IP address.
NOTE
When using a DME Satellite together with the DME64N/24N, you must assign the DME Satellite (including the DME8i-
ES/DME8o-ES/DME4io-ES) as the master. If you assign the DME64N/24N as the device group master, you will be unable to
synchronize using DME Designer.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
23
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to a Computer
Ethernet Connection ([NETWORK] Connector)
To control the DME Satellite from the computer via Ethernet, use an Ethernet cable to connect the [NET-
WORK] connector on the rear panel of the DME Satellite to the computer, then install DME-N Network Driver.
NOTE
• Refer to the “DME Setup Manual” (PDF file) for details on installing DME-N Network Driver.
• Appropriate IP addresses must first be assigned to all devices connected to an Ethernet network. Connect your computer to
one of the DME Satellite units via USB, then assign the IP addresses from DME Designer (page 22).
Two DME Satellite units directly connected via Ethernet
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
Ethernet Cable
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
USB Cable
You can connect devices in the same device group directly to each other using Ethernet cables, without connecting
them to a switching hub. If they are DME Satellite units, you can use either crossover cables or straight cables. In
this case, from DME Designer set Link Mode on both units to the same setting. Devices in different subnet (dif-
ferent network address) groups can be connected via a router or layer-3 compliant switching hub.
HINT
Since the DME Satellite supports Auto MDI/MDI-X, it will automatically detect whether the connected cable is of the
straight type or crossover type, and will configure itself to create the optimal connection. Therefore, you can use either a
straight or crossover cable.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
24
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to a Computer
Control from a computer in the same subnet group
Device Group
Group Master
INPUT
PE
SIGNAL
PE
A
K
A
K
PE
AK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite (IP address: 192.168.0.7)
Ethernet Cable
Ethernet Straight Cable
Switching Hub
Ethernet Cable
Ethernet
Straight Cable
Computer
(IP address:
192.168.0.100)
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
SCENE
HOME
UTILITY
LEVEL
MUTE
CANCEL
ENTER
DME Satellite
(IP address: 192.168.0.3)
(Master ID: 7)
DME64N/24N
(IP address: 192.168.0.250)
(Master ID: 7)
NOTE
• The IP addresses in the diagram are examples.
• Use a switching hub that is compatible with 100Base-TX/10Base-T network speeds.
The maximum length of a cable between a switching hub and the DME Satellite is 100 meters. Due to the quality of cables
and switching hub performance, however, proper operation at the maximum length cannot be guaranteed in some cases.
Use a STP (Shielded Twisted Pair) cable to prevent electromagnetic interference.
• If you are using multiple DME series units, set Link Mode on each unit to the same setting. Yamaha recommends that you
select 100Base-TX for the Link Mode setting.
• You can also connect a supported controller such as the AMX or Crestron, and control the DME Satellite remotely. For
details, refer to “Connecting to an External Device” on page 30.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
25
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to a Computer
Control from a computer with a different subnet
Device Group
Port settings
Group Master
• Destination network address: 192.168.0.0
• Subnet mask: 255.255.255.0
• Gateway: 192.168.0.254
INPUT
PE
SIGNAL
PE
A
K
A
K
PE
AK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite (IP address: 192.168.0.5)
Ethernet Cable
Ethernet
Straight Cable
Router or
Layer-3
Compliant
Switching
Hub
Switching Hub
Ethernet
Straight Cable
Ethernet Cable
Computer
Ethernet
Straight Cable
INPUT
PE
A
K
PEA
K
PE
AK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
(IP address: 192.168.0.3)
(Master ID: 5)
SCENE
HOME
UTILITY
LEVEL
MUTE
CANCEL
ENTER
DME64N/24N
(IP address: 192.168.0.12)
(Master ID: 5)
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
26
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to a Computer
Connecting multiple device groups
Device Group 1
Device Group 2
Group Master
Group Master
INPUT
PE
SIGNAL
INPUT
PE
SIGNAL
PE
A
K
A
K
PE
A
K
PE
A
K
A
K
PE
AK
DIGITAL MIXING ENGINE SATELLITE
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
SIGNAL
USB
USB
PEA
K
PEA
K
PEA
K
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
INPUT
INPUT
DME Satellite
DME Satellite
(IP address: 192.168.0.2)
(IP address: 192.168.0.3)
Ethernet Cable
Ethernet Cable
Switching Hub
Switching Hub
Ethernet Straight Cable
Ethernet Straight Cable
Ethernet
Straight Cable
Ethernet Cable
SCENE
HOME
UTILITY
LEVEL
MUTE
CANCEL
ENTER
SCENE
HOME
UTILITY
LEVEL
MUTE
CANCEL
ENTER
DME64N/24N
Ethernet Cable
DME64N/24N
(IP address: 192.168.0.100)
(Master ID: 2)
(IP address: 192.168.0.200)
(Master ID: 3)
INPUT
INPUT
PEA
K
PEA
K
PEA
K
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
USB
USB
PEA
K
PEA
K
PEA
K
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
SIGNAL
INPUT
INPUT
DME Satellite
(IP address: 192.168.0.40)
(Master ID: 2)
DME Satellite
(IP address: 192.168.0.10)
(Master ID: 3)
Computer
(IP address: 192.168.0.1)
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
27
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Audio I/O Connection
Digital Audio Connection (CobraNet Connectors)
The DME Satellite CobraNet connectors enable you to transfer digital audio, control, and word clock signals. Re-
Connecting and setting up the DME Satellite in accordance with other CobraNet compatible equipment allows
for broad-ranging audio and word clock signal networkability. Refer to the MY16-C or MY16-CII Owner’s Man-
ual for more information on the corresponding interface card.
Example: Connection to CobraNet devices
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
ACU16-C
Audio Signal
Audio Signal
Audio Signal
Audio Signal
NETWORK HUB AND BRIDGE
Switching Hub
MY16-CII
Ethernet Straight Cable
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
EXT
CLOCK
.
NETWORK
MID
PEAK
96kHz
88.2kHz
48kHz
MASTER
SIGNAL
1
IN
44.1kHz
PEAK
SCENE NUMBER
SIGNAL
OUT
LINK CONDUCT
ERROR
LOCK
DME24N
NHB32-C
NOTE
DME Satellites and the MY16-C or MY16C-II can transmit and receive control data such as for internal head amps via
CobraNet. However in some cases, it may not be possible to transmit or receive control data depending on the device in which
the MY card is installed. For details, refer to the operating manual of the device in which the card is installed.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
28
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Audio I/O Connection
Analog Audio Connection ([INPUT] & [OUTPUT] Connectors)
The DME Satellite can directly input and output audio signals via the [INPUT] and [OUTPUT] connectors.
Wire the supplied Euroblock plugs (3P) as shown below. You can use DME Designer to set the head amplifier
gain and turn the phantom power on and off for each [INPUT] connector.
Cable preparation
Prepare cables to be attached to a Euroblock plug as shown below.
Shielded Cable
7mm
30mm
Be sure to use shielded cables.
CAUTION
Do not tin (plate with solder) the exposed sections of the cable.
CAUTION
Euroblock plug connection
NOTE
Use a slotted screwdriver with a blade width of about 3 millimeters to secure the cables to the
(3P) Euroblock plug.
3mm
Use a slotted screwdriver with a blade width of about 2 millimeters to secure the cables to the
(16P) Euroblock plug to connect to the [GPI] connector.
1. Loosen terminal screws.
Loosen
Slotted Screwdriver
Terminal Screw
Euroblock Plug
2. Insert cables.
3. Securely tighten terminal screws.
Pull the cables (not too strongly) to confirm that they are securely connected.
4. Insert the Euroblock plug into the Euroblock
connector on the rear panel.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
29
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to an External Device
Remote Connection ([REMOTE] Connector)
The [REMOTE] connector of the DME Satellite can be connected to remotely-controllable Yamaha AD8HR or
AD824 head amplifiers (pre-amps), digital mixers, or RS-232C compatible controllers (such as those from AMX
or Crestron). The [REMOTE] connector also transmits and receives MIDI messages.
Controlling external head amplifiers from the DME Satellite
You can remotely control the AD8HR or AD824 head amplifier settings from DME Designer. Up to eight
AD8HR/AD824 head amplifiers can be connected.
AD8HR or AD824 remote head amplifiers. Do not change the dip switch setting to any position other than to
“RS-422” while the devices are connected to prevent possible damage to the device(s).
When connecting to a combination of AD8HR and AD824 head amplifiers, be sure to place the AD8HR units
closest to the DME Satellite in the chain, otherwise the AD8HR or AD824 unit(s) may not be properly recognized
by the DME Satellite.
D-SUB 9-pin Cable (Interlink Crossover)
Set to RS-422
REMOTE
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
HA REMOTE 1
HA REMOTE 2
HA REMOTE 1
HA REMOTE 2
AD8HR
AD8HR
COM PC/RS-422
COM RS-422
COM PC/RS-422
COM RS-422
COM PC/RS-422
AD824
AD824
AD824
NOTE
Only control signals are transmitted and received via the REMOTE connection. Audio connections must be made separately.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
30
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to an External Device
Controlling a DME Satellite’s internal head amps from a digital mixer
The internal head amp settings of a DME8i-C or DME4io-C can be remotely controlled from a digital mixer such
as the Yamaha PM5D or DM2000.
Connect the digital mixer to the DME series’ [REMOTE] connector, and use an Ethernet cable to make connec-
tions between the [NETWORK] connectors of the DME series.
From the digital mixer, DME series units can be controlled as an AD8HR. The gain and the phantom power
(+48V) can be controlled.
D-SUB 9-pin Cable
REMOTE
REMOTE
Ethernet
Cable
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
DIGITAL MIXING ENGINE SATELLITE
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
Switching
Hub
DME Satellite
INPUT
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
Digital Mixer
INPUT
PE
A
K
PEA
K
PE
AK
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
DME Satellite
NOTE
• Only one mixer can be connected within each device group.
• The digital mixer can be connected to any DME series unit, whether it is the group master or a slave unit.
• The ID number of the DME series unit being remotely controlled is specified from DME Designer.
For details on making this setting, refer to the “DME Designer Owner’s Manual.”
• If the connection between DME series units is broken, it will no longer be possible to communicate with DME units of an
ID number that follows the disconnected DME.
• The variable range of GAIN differs between the AD8HR and the DME Satellite. You cannot use the mixer to specify a value
that exceeds the variable range of the DME Satellite.
Controlling the DME Satellite from an external device
You can remotely control the DME Satellite from a connected RS-232C or RS-422 compatible controller, such
as those from AMX or Crestron.
nected RS-232C or RS-422 compatible remote controller. Do not change the dip switch setting to any other po-
sition while the devices are connected to prevent possible damage to the device(s).
NOTE
• The port used for remote control is specified from DME Designer. For details on making this setting, refer to the “DME
Designer Owner’s Manual.”
• Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on communication
protocols used to control the DME Satellite from an external device (such as those from AMX or Crestron).
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
31
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to an External Device
CobraNet Connection (CobraNet Connectors)
You can use the CobraNet connector to control the DME Satellite’s internal head amp or other functionality.
Controlling DME Satellite’s internal head amps from a digital mixer Yamaha LS9
The internal head amp settings of a DME8i-C or DME4io-C can be remotely controlled from a digital mixer LS9.
Use the MY16-CII interface card to make CobraNet connections between the digital mixer and the DME series.
Use an Ethernet cable connected to the [NETWORK] connectors to make connections between DME series
units.
The gain and the phantom power (+48V) can be controlled from the digital mixer.
DME8i-C
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
SIGNAL
SIGNAL
SIGNAL
INPUT
Switching
Hub
DME8i-C
Switching
Hub
MY16-CII
Ethernet
CobraNet
Ethernet Switching Hub
CobraNet Switching Hub
LS9
NOTE
• Only one mixer can be connected within each device group.
• The digital mixer can be connected to any DME series unit, whether it is the group master or a slave unit.
• The ID number of the DME series unit being remotely controlled is specified from DME Designer.
For details on making this setting, refer to the “DME Designer Owner’s Manual.”
• If the connection between DME series units is broken, it will no longer be possible to communicate with DME units of an
ID number that follows the disconnected DME.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
32
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to an External Device
Controlling the DME Satellite from a digital mixer Yamaha PM5D
If you install an MY16-C or MY16-CII interface card on a PM5D Digital Mixing Consol and connect it to the
DME Satellite via the CobraNet connectors, you can remotely control the DME Satellite from the PM5D, as well
as transfer audio and word clock signals between them. Refer to the PM5D/PM5D-RH Owner’s Manual for more
information on the PM5D’s DME Control function.
DME8i-C
INPUT
PEA
K
PEA
K
PEAK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
PEA
K
PEA
K
PEAK
Ethernet
SIGNAL
SIGNAL
SIGNAL
INPUT
CobraNet
DME8i-C
INPUT
PE
A
K
PEA
K
PE
AK
DIGITAL MIXING ENGINE SATELLITE
SIGNAL
SIGNAL
SIGNAL
USB
Ethernet Switching Hub
CobraNet Switching Hub
PE
A
K
PE
A
K
PE
AK
SIGNAL
SIGNAL
SIGNAL
INPUT
Hub
Hub
DME8o-C
DME8o-C
DME4io-C
DME4io-C
Hub
MY16-CII
MY16-CII
PM5D
NOTE
• You can control multiple DME series units from a PM5D. Specify the same device group for each DME series unit you
want to control.
• If you have connected a PM5D and a DME Satellite via CobraNet and are controlling the DME Satellite from the PM5D,
you must specify a value of 2 as the fourth octet of the group master DME Satellite’s IP address.
Network Connection ([NETWORK] Connectors
You can connect a controller such as the AMX or Crestron to DME Satellites via Ethernet, and remotely control
multiple DME Satellite units.
NOTE
• The port used for remote control is specified from DME Designer. For details on making this setting, refer to the “DME
Designer Owner’s Manual.”
• Refer to “DME Remote Control Protocol Specifications” on the Yamaha web site for more information on communication
protocols used to control the DME Satellite from an external device (such as those from AMX or Crestron).
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
33
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Connecting to an External Device
GPI Connection ([GPI] Connector)
A GPI (General Purpose Interface) device (GPI controller, etc.) can be connected to the rear panel [GPI] connec-
tors to enable the transfer of a variety of control signals. Optional CP4SW, CP4SF, and CP1SF Control Panels
can be also connected via GPI.
The DME Satellite features 8-port GPI input and 4-port GPI output. The +V terminals have an output voltage
of 5 volts. The IN terminal detects voltage changes from 0V to 5V. The OUT terminals output either signal “L”
or “H” at a TTL level.
The parameters for each GPI input and output are assigned via the DME Designer application.
Euroblock connectors are used for all GPI input and output connections. Euroblock connection methods are de-
NOTE
• For more information on the CP4SW, CP4SF, and CP1SF Control Panels, refer to the CP4SW/CP4SF/ CP1SF Owner’s
Manual.
• You can use DME Designer to set up the system so that scene recall operations and User Defined parameter control can be
carried out from connected GPI control devices. Refer to the DME Designer Owner’s Manual for details.
Example: Controlling the DME
Satellite from a switch box
Example: Controlling the DME Satellite via a
10k ohm linear taper potentiometer.
Example: Lighting LED indicators on the
external devices from the DME Satellite
GPI Connection
GPI Connection
GPI Connection
OUT GND
IN
+V
GND
IN
+V
Max. 16mA
Continuous Variable Volume
Make sure that the current between the
OUT and GND [GPI] connectors is
CAUTION
less than 16mA.
DME Satellite [GPI] Connector
Euroblock Plug
DME Satellite [GPI] Connector
Euroblock Plug
DME Satellite [GPI] Connector
Euroblock Plug
Remote Switch Box
Remote Fader Box
Remote LED Box
4
3
2
1
4
3
2
1
4
3
2
1
Switches
LEDs and Resistors
10k ohm Linear
Taper Potentiometer
NOTE
You can use DME Designer to adjust the input calibration parameters for the [GPI] connector.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
34
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Other Functions
Initializing the DME Satellite
You can initialize the DME Satellite internal memory.
Select one of the following initialization types:
Initialize DME:
All scenes, preset parameter settings and WAVE files except components and files saved via the File Storage func-
tion will be deleted. The Utility settings will be set to default values.
Delete All Data:
All stored component, scene, and preset parameter settings, WAVE files, and files saved via the File Storage func-
tion will be deleted. The Utility settings will be set to default. Use this initialization type if the internal data is
damaged or corrupted. After initialization, transfer necessary components from DME Designer.
1. While the DME Satellite is turned off, set the dip switch on the rear panel to the following
position, then turn on the power to the unit.
RS-232C
Initialize DME:
RS-422
RS-232C
Delete All Data:
RS-422
Four [PEAK] indicators on the upper row on the front panel light up during the initialization process. Four
[SIGNAL] indicators on the lower row of the front panel flash when the initialization process is complete. Four
[PEAK] indicators on the lower row of the front panel flash if the initialization process fails.
Do NOT turn off the power to the DME Satellite during the initialization process to prevent possible
damage to the device.
CAUTION
then turn off and on the power to the unit.
Be sure to reset the dip switch to the previous position to prevent possible damage to the device.
CAUTION
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
35
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
Options
The ICP1, CP4SW, CP1SF, and CP4SF controllers are available as options for remote external control of the DME series. The
ICP1 connects via Ethernet, while the CP4SW, CP1SF, and CP4SF connect via the GPI interface. For more information on
installing your Control Panel and connecting it to a DME series unit, refer to the owner’s manual that came with the Control
Panel. For more information on settings, refer to the DME Designer Owner’s Manual.
ICP1
This controller connects to a DME series unit via Ethernet. Like the DME series units, a unique IP address must
be assigned to each controller unit. Data is transmitted and received via Ethernet cables.
You can assign and control any function of all DME series units in the same device group via the controller.
Up to four parameter sets can be assigned to six function keys (F1 – F6) located above and under the LCD. You
can control up to 24 parameters by selecting a display page using the [HOME] key.
CP4SW, CP4SF, and CP1SF
These controllers connect to DME series units via the [GPI] connectors. These controllers control only the DME
series units to which they are directly connected. The controller switches enable you to turn the parameter settings
On and Off. The switch LEDs enable you to check the parameter status. The faders enable you to control the
parameter values.
10
10
10
10
10
0
0
0
0
0
CONTROL PANEL
CP4SF
CONTROL PANEL
CP1SF
CONTROL PANEL
CP4SW
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
36
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
Troubleshooting
• If the device still does not turn on, contact a Yamaha dealer.
The device does not turn on, or the panel
LEDs do not light up.
• Make sure that USB-MIDI Driver has been installed correctly.
• If the [NETWORK] connector is being used for connection, make sure that you have set
the DME-N Network Driver correctly.
No communication between the DME
Satellite and the DME Designer
application software.
• Make the “MIDI Setup” settings.
• The DME Designer version should be 3.0 or later.
• Make the Port setting.
• Connect the cable properly.
No audio input is present.
No audio is output.
• Check to see if signals are being received from an external device.
• Make sure that the CobraNet bundle and latency settings are correct.
• Set the gain of the internal head amplifier or external head amplifier to an appropriate
level.
• Connect the cable properly.
• Make sure that the CobraNet bundle and latency settings are correct.
• Make sure that the number of CobraNet multicast bundles is not exceeding the
recommended maximum number.
• Depending on the type of switching hub and connection method, extra network resources
may have been used, resulting in interruption of audio signals.
• Make sure that the output level set in DME Designer is not too low.
• Make sure that the Mute setting in DME Designer is set to Off.
• You may have designed a scene in DME Designer that mutes audio output.
• You may have tried to use a configuration at 96 kHz that does not support 96 kHz.
The selected scene changes
unexpectedly.
• Use DME Designer to check the MIDI Program Change assignments.
• Use DME Designer to check the GPI input assignments.
• Make sure that the power to the MIDI device is turned on.
• Set the MIDI port properly.
• Set the receive and transmit channels properly.
MIDI messages cannot be transmitted or
received.
• Use DME Designer to change the setting so that the required MIDI Program Change
messages will be received properly.
• Make the appropriate Program Change Table settings via DME Designer.
Scenes cannot be recalled via MIDI
Program Change messages.
• Use DME Designer to set the parameters correctly to allow Control Change message
reception.
• Make the appropriate MIDI Control Change Table settings via DME Designer.
Parameters cannot be controlled via MIDI
Control Change messages.
• Use DME Designer to set the parameters correctly to allow Parameter Change message
reception.
• Make the appropriate MIDI Parameter Change Table settings via DME Designer.
Parameters cannot be edited via MIDI
Parameter Change messages.
Component
Refer to the DME Designer Owner’s Manual for more information on each component.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
37
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
MIDI Data Format
3. MIDI Setup
Specifies basic MIDI operation. Use DME Designer to make the
setting.
1. MIDI functions on the DME8i-C,
DME8o-C, and DME4io-C
3.1 Host Select
1.1 Scene Change
Selects the input/output ports to be used for MIDI communica-
tion.
Scene recall occurs according to the “MIDI Program Change Ta-
ble” assignments when appropriate MIDI Bank Select MSB/LSB
and Program Change messages are received by the DME8i-C/
DME8o-C/DME4io-C.
3.2 MIDI Tx Channel
Specifies the MIDI transmit channel (1 ~ 16).
When a scene recall operation is carried out via DME Designer,
corresponding MIDI Bank Select MSB/LSB and Program Change
messages are also transmitted by the DME8i-C/DME8o-C/
DME4io-C as specified by the “MIDI Program Change Table” as-
signments.
3.3 MIDI Rx Channel
Specifies the MIDI receive channel (1 ~ 16).
3.4 MIDI Tx Switch
Program Change Tx Switch: turns Bank Select MSB, LSB, and
Program Change transmission on or off.
Control Change Tx Switch: turns Control Change transmission on
or off.
Parameter Change Tx Switch: turns Parameter Change transmis-
sion on or off.
Transmission does not occur while configurations are being
switched.
1.2 Parameter Control
MIDI Control Change and Parameter Change messages trans-
mitted to the DME8i-C/DME8o-C/DME4io-C can be used
to control parameters according to the “MIDI Control Change
Table” and “MIDI Parameter Change Table” assignments.
3.5 MIDI Rx Switch
Program Change Rx Switch: turns Bank Select MSB, LSB, and
Program Change reception on or off.
Control Change Rx Switch: turns Control Change reception on or
off.
Parameter Change Rx Switch: turns Parameter Change reception
on or off.
When a parameter is edited via DME Designer, correspond-
ing MIDI Control Change and Parameter Change messages
are also transmitted by the DME8i-C/DME8o-C/DME4io-
C as specified by the “MIDI Control Change Table” and
“MIDI Parameter Change Table” assignments.
3.6 MIDI Omni Switch
“MIDI Program Change Table,” “MIDI Control Change Table,” and “MIDI
Parameter Change Table” assignments can be made via DME Designer.
Refer to the DME Designer Owner’s Manual for details.
Program Change Omni Switch: turns the Bank Select MSB, LSB,
and Program Change omni mode on or off.
Control Change Omni Switch: turns the Control Change omni
mode on or off.
2. MIDI Data Flow
3.7 MIDI Echo Back Switch
Program Change Echo Back Switch: turns Bank Select MSB, LSB,
and Program Change echo back on or off.
Control Change Echo Back Switch: turns Control Change echo
back on or off.
Parameter Change Echo Back Switch: turns Parameter Change
echo back on or off.
MIDI IN
Bank Select MSB/LSB
Program Change
(Scene Recall)
MIDI Rx CH
SW1
Control Change
(Parameter Edit)
SW2
SW3
Parameter Change
(Parameter Edit)
Bank Select MSB/LSB
Program Change
(Echo Back)
SW4
SW5
SW6
Control Change
(Echo Back)
Parameter Change
(Echo Back)
Bank Select MSB/LSB
Program Change
MIDI Tx CH
MIDI OUT
SW7
SW8
SW9
Control Change
Parameter Change
MIDI THRU
SW1:
SW2:
SW3:
SW4:
SW5:
SW6:
SW7:
SW8:
SW9:
Program Change Rx Switch [On/Off]
Control Change Rx Switch [On/Off]
Parameter Change Rx Switch [On/Off]
Program Change Echo Back Switch [On/Off]
Control Change Echo Back Switch [On/Off]
Parameter Change Echo Back Switch [On/Off]
Program Change Tx Switch [On/Off]
Control Change Tx Switch [On/Off]
Parameter Change
MIDI Rx CH:MIDI Rx Channel (1-16)
MIDI Tx CH:MIDI Tx Channel (1-16)
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
38
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
Bank Select MSB
4. MIDI Format
Status Bnh (1101nnnnb) Control Change
Data
00h (00000000b) Control Change No. 0 (Bank
Select MSB)
Data
nnh (0nnnnnnnb) Control Value (Bank Select
MSB No.)
Number Format Notation
Numbers ending with “h” are in hexadecimal format, while numbers
ending with “b” are binary format.
Bank Select LSB
Characters “A” through “F” in hexadecimal numbers represent decimal
values 10 through 15. Other lower-case characters (usually “n” or “x”)
can represent any number.
Status Bnh (1101nnnnb) Control Change
Data
20h (00100000b) Control Change No. 32 (Bank
Select LSB)
nnh (0nnnnnnnb) Control Value (Bank Select
LSB No.)
MIDI Format Chart (Rx: receive, Tx: transmit}
Command
Rx/Tx
Function
Program Change No.
Control Change
(Bnh)
Editing the
parameters
Status Cnh (1100nnnnb) Program Change
Rx/Tx
Channel
Data
nnh (0nnnnnnnb) Program Change No. (0-127)
Message
Program Change
(Cnn)
Rx/Tx
Rx
Scene Recall
4.2 Active Sensing (FEh)
Receive
TIMING CLOCK
(F8h)
MIDI Clock
Receive
MIDI communication will be initialized if no data is received with-
in 300 ms after reception (Running Status, etc., will be cleared).
System Real-time
Message
ACTIVE SENSING
(FEh)
MIDI Cable
Check
Rx
Active Sensing
Status FEh (11111110b) Active Sensing
System Exclusive
Message
Parameter
Change
Editing the
parameters
Rx/Tx
4.3 Control Change (Bnh)
Receive
4.1 Program Change (Cnh)
Receive
When the “Program Change Rx Switch” is on, Program Change
messages are received on the MIDI channel specified by the “MIDI
Rx Channel” parameter.
If the “Program Change Omni Switch” is also on, however, Pro-
gram Change messages will be received on all MIDI channels re-
gardless of the “MIDI Rx Channel” setting.
When the “Control Change Rx Switch” is on, Control Change
messages are received on the MIDI channel specified by the “MIDI
Rx Channel” parameter.
If the “Control Change Omni Switch” is also on, however, Control
Change messages will be received on all MIDI channels regardless
of the “MIDI Rx Channel” setting.
Control Change parameter resolution is 128 regardless of the effec-
tive range of the parameter.
For finer settings use Parameter Change.
When a Program Change message is received, the scene assigned to
the received program number in the “MIDI Program Change Ta-
ble” is recalled.
Transmit
When the “Control Change Tx Switch” is on and a parameter is ed-
ited via DME Designer, appropriate Control Change data will be
transmitted as specified by the “MIDI Control Change Table” and
“MIDI Tx Channel” settings.
Refer to “Supplementary Information 1” for cases in which multi-
ple messages are assigned to a single parameter.
The effective Bank Select, Program Change range is as follows:
Bank Select MSB:
Bank Select LSB:
0
0-7
Program Change No.: 0-127
Transmit
Status Bnh (1011nnnnb) Control Change
When the “Program Change Tx Switch” is on and a scene is
switched from DME Designer, the corresponding Program Change
number will be transmitted as specified by the “MIDI Program
Change Table” and “MIDI Tx Channel” settings.
If multiple Program Change numbers are assigned to a single scene,
the Bank Select MSB/LSB and Program Change number corre-
sponding to the lowest number will be transmitted.
Data
cch (0cccccccb) Control Change No. (1-31,33-
95,102-119)
vvh (0vvvvvvvb) Control Value (0-127)
4.4 Parameter Change (F0h - F7h)
Receive
When the “Parameter Change Rx Switch” is On, Parameter
Change messages are received on the MIDI channel specified by the
“Device ID (Rx Ch)” parameter.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
39
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
Transmit
Supplementary Information 1
When the “Parameter Change Tx Switch” is On and a parameter is
edited via DME Designer, appropriate Parameter Change data will
be transmitted as specified by the “MIDI Parameter Change Table”
and “MIDI Tx Channel” settings.
Refer to “Supplementary Information 1” for cases in which multi-
ple messages are assigned to a single parameter.
Refer to “Supplementary Information 2” for information on setting
Parameter Data values.
Messages Transmitted When Multiple Messages are Assigned to
the Same Parameter
The DME8i-C/DME8o-C/DME4io-C MIDI transmit messages
are specified via the “MIDI Control Change Table” and “MIDI Pa-
rameter Change Table.”
(The “MIDI Control Change Table” and “MIDI Parameter
Change Table” can be set up via DME Designer.)
Multiple messages can be assigned to a single parameter, but the
DME8i-C/DME8o-C/DME4io-C will only transmit one of the as-
signed messages.
The transmitted messages are as follows:
• If a Control Change message and a Parameter Change message
are assigned to the same parameter
Status
ID No.
F0h (11110000b) System Exclusive Message
43h (01000011b) Manufacturer’s ID
No.(YAMAHA)
DEVICE ID. 1xh (0001xxxxb) Rx/Tx Channel (0-15)
GROUP ID. 3Eh (00111110b) Digital Mixer
MODEL ID. 10h (00010000b) Device Code (DME)
Parameter aah (0aaaaaaab) Parameter Address High
Address
→ the Control Change message will be transmitted.
• If multiple Control Change numbers are assigned to the same pa-
rameter
→ the smallest Control Change number message will be trans-
mitted.
aah (0aaaaaaab) Parameter Address Low
Parameter ddh (0dddddddb) data 0
Data Value
ddh (0dddddddb) data 1
• If multiple Parameter Change numbers are assigned to the same
parameter
ddh (0dddddddb) data 2
ddh (0dddddddb) data 3
→ the smallest Parameter Change number message will be trans-
mitted.
ddh (0dddddddb) data 4
EOX
F7h (11110111b) End of Exclusive
Supplementary Information 2
Setting the Parameter Change Message Parameter Data Values
The Parameter change parameter values are expressed as 32-bit in-
tegers with or without parity.
• A parity bit (positive:0, negative:1) is added above the most sig-
nificant value bit (bit 31).
• Fractional parameters will be converted according to the integer
table.
• For integers with parity, negative numbers are expressed as the
2’s complement.
0 0
data 0
data 1
data 2
data 3
data 4
Example:
• Decimal value 1000 → Hexadecimal value 3E8h
0
0
0
0
0
3
E
8
Positive
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 1 0 0 0
data 0 = 00h
data 1 = 00h
data 2 = 00h
data 3 = 07h
data 4 = 68h
• Decimal value 1000 → Hexadecimal value FFFFFC18h (2’s complement of 3E8h)
Negative
F
F
F
F
F
C
1
8
0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 1 0 0 0
data 0 = 1Fh
data 1 = 7Fh
data 2 = 7Fh
data 3 = 78h
data 4 = 18h
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
40
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
MIDI Implementation Chart
YAMAHA [Digital Mixing Engine Satellite]
Date :16-FEB-2006
Version : 1.0
Model DME8i-C, DME8o-C, DME4io-C MIDI Implementation Chart
Function...
Transmitted
Recognized
1 - 16
Remarks
Basic
Default 1 - 16
Changed 1 - 16
Memorized
Channel
1 - 16
Default
Messages
Altered **************
˛
˛
˛
˛
˛
Mode
Note
˛
˛
˛
Number : True voice **************
Velocity
Note ON
Note OFF
˛
˛
˛
˛
After
Touch
Key's
Ch's
˛
˛
˛
˛
Pitch Bend
˛
˛
0,32
Ø
Ø
*1
*2
Ø
Ø
*1
*2
Bank Select
Assignable
1-31,33-95,102-119
Control
Change
Prog
Ø 0 - 127
*1
*3
Ø 0 - 127
*1
Change : True # **************
0 - 127
System Exclusive
: Song Pos.
Common : Song Sel.
: Tune
Ø
Ø
*3 Assignable
˛
˛
˛
˛
˛
˛
System
Real Time : Commands
: Clock
˛
˛
˛
˛
: AllSoundOff
Aux : Reset All Cntrls
: Local ON/OFF
Mes- : AllNotesOFF
sages: Active Sense
: Reset
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
˛
Notes:
*1 transmit/receive if program change switch is on.
*2 transmit/receive if control change switch is on.
*3 transmit/receive if parameter change switch is on.
Mode 1 : OMNI ON , POLY
Mode 3 : OMNI OFF, POLY
Mode 2 : OMNI ON ,MONO
Mode 4 : OMNI OFF,MONO
Ø : Yes
˛ : No
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
41
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
Display Messages
The [ERROR] and [PEAK] indicators on the front panel of the DME Satellite indicate error and warning messages.
Error Messages
Indicator
Error
Action
A system error has occurred.
Execute the “Initialize DME” operation, then restart it. If the error
indicators are still indicating the error, execute the “Delete All Data”
initialization. If the problem persists, contact a Yamaha dealer.
Flashing
PEAK
PEAK
PEAK
Lit
SIGNAL
SIGNAL
SIGNAL
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
Data inside the internal flash
memory has been erased.
The firmware update operation may have failed. Use DME Designer
to execute the Recovery update operation. If the problem persists,
contact a Yamaha dealer.
Flashing
PEAK
PEAK
PEAK
Lit
Lit
Lit
SIGNAL
SIGNAL
SIGNAL
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
The internal battery is
completely discharged or not
installed.
If you turn off the power to the unit, the current settings will be lost
and reset to the default values. Stop operating the unit, and contact a
Yamaha dealer regarding battery replacement.
Flashing
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
A scene recall attempt has
failed.
Use DME Designer to recall the scene again.
If the problem persists, contact a Yamaha dealer.
Flashing
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
Audio is not input or output and
is muted due to insufficient DSP
resources.
This error sometimes occurs if you try to operate a configuration at 96
kHz that has been created with a word clock of 48 kHz. To operate a
configuration at any word clock setting, use DME Designer to create
a configuration with the word clock set to 96 kHz.
PEAK
PEAK
PEAK
Lit
SIGNAL
SIGNAL
SIGNAL
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
Flashing
The network is not
communicating properly.
Connect the network cables properly, and make sure that the
network devices are operating correctly.
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
Lit
Lit
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
Flashing
Duplicate IP addresses.
Connect your computer to the DME Satellite via USB, then set a
unique IP address.
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
Flashing
The DME Satellite contains data
for a different device group or
no data.
Send data appropriate for the actual device configuration from DME
Designer.
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
Lit
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
Flashing
Warning Messages
Indicator
Error
Action
The internal battery is almost
discharged. Your data may be
lost.
If you turn off the power to the unit, the current settings may
be lost and reset to the default values. Stop operating the
unit, and contact a Yamaha dealer regarding battery
replacement.
PEAK
PEAK
PEAK
Flashing
rapidly
SIGNAL
SIGNAL
SIGNAL
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
The backup battery voltage is
low.
This does not affect the operation of the unit. However, if you
continue using the unit, the settings may be lost and reset to
the default values. Contact a Yamaha dealer regarding
battery replacement at your earliest convenience.
PEAK
PEAK
PEAK
Flashing
SIGNAL
SIGNAL
SIGNAL
slow
PEAK
PEAK
PEAK
SIGNAL
SIGNAL
SIGNAL
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
42
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
General Specifications
Normal Rate:48kHz
Double Rate:96kHz
Sampling Frequency
( 37ppm for conductor)
( 50ppm for performer)
Maximum Voltage Gain
Gain: –60dB, RL:600Ω, 64dB INPUT to OUTPUT
Power Consumption
Dimensions (HxDxW)
Net Weight
40W
44x361x480 mm
4.4kg
Miscellaneous
operating: 5 to 40˚C
storage: –20 to 60˚C
Temperature range
Include Accessories
AC Power cord, Mini Euro plug(16P)x1, Euro plug(3P)x8, Owner’s Manual,
Rubber feetx4
Electrical Characteristics
Output impedance of signal generator: 150 Ω
DME8i-C : Measured with DME8o-C
DME8o-C : Measured with DME8i-C
DME4io-C: Measured with DME4io-C
Frequency Response
fs=48kHz@20Hz–20kHz, reference to the nominal output level @1kHz
fs=96kHz@20Hz–40kHz, reference to the nominal output level @1kHz
<DME8i-C>
Input
Output
RL
CONDITIONS
MIN
–1.5
–1.5
TYP
0.0
MAX
+0.5
+0.5
UNITS
dB
input level: –60dBu, GAIN: –60dB
input level: +10dBu, GAIN: +10dB
INPUT 1–8
OUTPUT 1–8
600Ω
0.0
dB
<DME8o-C>
Input
Output
RL
CONDITIONS
MIN
TYP
MAX
UNITS
INPUT 1–8
OUTPUT 1–8
600Ω
input level: +10dBu, GAIN: +10dB
–1.5
0.0
+0.5
dB
<DME4io-C>
Input
Output
RL
CONDITIONS
MIN
–1.5
–1.5
TYP
0.0
MAX
+0.5
+0.5
UNITS
dB
input level: –60dBu, GAIN: –60dB
input level: +10dBu, GAIN: +10dB
INPUT 1–4
OUTPUT 1–4
600Ω
0.0
dB
Gain Error
<DME8i-C>
@1kHz
Input
Output
RL
CONDITIONS
MIN
+2.0
+2.0
TYP
+4.0
+4.0
MAX
+6.0
+6.0
UNITS
dBu
input level: –60dBu, GAIN: –60dB
input level: +10dBu, GAIN: +10dB
INPUT 1–8
OUTPUT 1–8
600Ω
dBu
<DME8o-C>
Input
Output
RL
CONDITIONS
MIN
TYP
MAX
UNITS
INPUT 1–8
OUTPUT 1–8
600Ω
input level: +10dBu, GAIN: +10dB
+2.0
+4.0
+6.0
dBu
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
43
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
<DME4io-C>
Input
Output
RL
CONDITIONS
MIN
+2.0
+2.0
TYP
+4.0
+4.0
MAX
+6.0
+6.0
UNITS
dBu
input level: –60dBu, GAIN: –60dB
input level: +10dBu, GAIN: +10dB
INPUT 1–4
OUTPUT 1–4
600Ω
dBu
Total Harmonic Distortion
<DME8i-C/DME4io-C>
fs=48kHz or 96kHz
Input
Output
RL
CONDITIONS
MIN
TYP
MAX
UNITS
+4dB@20Hz–20kHz (fs=48kHz),
20Hz–40kHz (fs=96kHz), GAIN: –60dB
0.1
%
<DME8i-C>
INPUT 1–8
+4dB@20Hz–20kHz (fs=48kHz),
20Hz–40kHz (fs=96kHz), GAIN: +10dB
0.05
%
OUTPUT 1–8
600Ω
<DME4io-C>
INPUT 1–4
+22dB@1kHz, GAIN: +10dB (fs=48kHz)
+22dB@1kHz, GAIN: +10dB (fs=96kHz)
0.015
0.007
%
%
<DME8o-C>
Input
Output
RL
CONDITIONS
MIN
TYP
MAX
UNITS
+4dB@20Hz–20kHz (fs=48kHz),
20Hz–40kHz (fs=96kHz), GAIN: +10dB
0.05
%
INPUT 1–8
OUTPUT 1–8
600Ω
+22dB@1kHz, GAIN: +10dB (fs=48kHz)
+22dB@1kHz, GAIN: +10dB (fs=96kHz)
0.015
0.007
%
%
* Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz.
Hum&Noise
<DME8i-C>
fs=48kHz or 96kHz, EIN=Equivalent Input Noise
Input
Output
RL
CONDITIONS
MIN
TYP
MAX
UNITS
dBu
–128
EIN
–127
EIN
Rs=150Ω, GAIN: –60dB
All input & output level controls: 0dB
INPUT 1–8
OUTPUT 1–8
600Ω
–64
–82
dBu
Rs=150Ω, GAIN: +10dB
All input & output level controls: 0dB
–79
dBu
<DME8o-C>
Input
Output
RL
CONDITIONS
MIN
TYP
MAX
UNITS
Rs=150Ω, GAIN: +10dB
All input & output level controls: 0dB
INPUT 1–8
OUTPUT 1–8
600Ω
–82
–79
dBu
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
44
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
<DME4io-C>
Input
Output
RL
CONDITIONS
MIN
TYP
MAX
UNITS
–128
EIN
–127
EIN
dBu
Rs=150Ω, GAIN: –60dB
All input & output level controls: 0dB
INPUT 1–4
OUTPUT 1–4
600Ω
–64
–82
dBu
dBu
Rs=150Ω, GAIN: +10dB
All input & output level controls: 0dB
–79
*
Hum & Noise are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave
attenuation.
Dynamic Range
fs=48kHz or 96kHz
<DME8i-C/DME8o-C>
Input
Output
RL
CONDITIONS
MIN
MIN
TYP
MAX
MAX
UNITS
INPUT 1–8
OUTPUT 1–8
600Ω
GAIN: +10dB
106
dB
<DME4io-C>
Input
INPUT 1–4
*
Output
RL
CONDITIONS
TYP
UNITS
OUTPUT 1–4
600Ω
GAIN: +10dB
106
dB
Dynamic range are measured with a 6dB/octave filter @12.7kHz; equivalent to a 20kHz filter with infinite dB/octave
attenuation.
Crosstalk@1kHz
reference to the level of output N
<DME8i-C/DME8o-C>
from
to
CONDITIONS
MIN
MIN
TYP
TYP
MAX
UNITS
INPUT N
OUTPUT (N–1) or (N+1)
N = 1–8, GAIN: +10dB
–80
dB
<DME4io-C>
from
INPUT N
*
to
CONDITIONS
MAX
UNITS
OUTPUT (N–1) or (N+1)
N = 1–4, GAIN: +10dB
–80
dB
Crosstalk is measured with a 18dB/octave filter @80kHz
LED Level Meter
<DME8i-C>
METERING POINT
CONDITIONS
MIN
MIN
TYP
–3
MAX
MAX
UNITS
dBFs
PEAK red LED: ON
INPUT 1–8
SIGNAL green LED: ON
–40
dBFs
<DME8o-C>
METERING POINT
CONDITIONS
PEAK red LED: ON
SIGNAL green LED: ON
TYP
–3
UNITS
dBFs
OUTPUT 1–8
–40
dBFs
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
45
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
<DME4io-C>
METERING POINT
CONDITIONS
PEAK red LED:ON
SIGNAL green LED:ON
MIN
TYP
–3
MAX
UNITS
dBFs
INPUT 1–4
OUTPUT 1–4
–40
dBFs
Signal Delay
PARAMETER
CONDITIONS
MIN
TYP
6.12
3.45
2.12
MAX
UNITS
msec
msec
msec
CobraNet Latency: 5.33msec
CobraNet Latency: 2.67msec
CobraNet Latency: 1.33msec
ANALOG INPUT to ANALOG
OUTPUT@96KHz
Input/Output Characteristics
ANALOG INPUT CHARACTERISTICS
Input Terminals
GAIN
Actual Load
Impedance
For Use With
Nominal
Input Level
Connector
Nominal
Max.before clip
<DME8i-C>
CH INPUT 1–8
–60dBu
(0.775mV)
–40dBu
(7.75mV)
–60dB
+10dB
50–600Ω Mics &
600Ω Lines
EUROBLOCK
(5.08mm pitch)
3kΩ
+10dBu
(2.45V)
+30dBu
(24.5V)
<DME4io-C>
CH INPUT 1–4
*1.In these specifications, 0dBu is referenced to 0.775 Vrms.
*2.All AD converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz).
*3.+48V DC (Phantom power) is supplied to CH INPUT EUROBLOCK connectors via each individual software
controlled switch.
ANALOG OUTPUT CHARACTERISTICS
Output Terminals
Actual Source
Impedance
For Use With
Nominal
Output level
Connector
Nominal
Max. before clip
<DME8o-C>
CH OUTPUT 1–8
EUROBLOCK
(5.08mm pitch)
75Ω
600Ω Lines
+4dBu (1.23 V)
+24dBu(12.28V)
<DME4io-C>
CH OUTPUT 1–4
*1.In these specifications, 0dBu is referenced to 0.775 Vrms.
*2.All DA converters are 24-bit linear, 128-times oversampling (Fs=48kHz)/64-times oversampling (Fs=96kHz).
DIGITAL INPUT & OUTPUT CHARACTERISTICS
Terminal
Format
CobraNet
Data length
Level
Connector
CobraNet
16/20/24bit
100Base-TX
RJ-45x2 *1
*1.PRIMARY,SECONDARY
*2.Double Channel format and Single format are supported at 96kHz.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
46
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
CONTROL I/O CHARACTERISTICS
Terminal
Format
Level
Connector
EUROBLOCK *1
(3.5mm pitch)
IN
–
0–5V
GPI
OUT
–
TTL
+V
Ethernet
–
5V
10Base-T/100Base-TX
–
IEEE802.3
USB 1.1 Function
RS-232C/RS-422
RJ-45
Type B
USB
REMOTE
RS-232C/RS-422
D-SUB 9P (Male)
*1 Inputs: 8 channels, Outputs: 4 channels
Inputs: Not apply 2 wire Fader mode
Outputs: Imax/pin = 16mA
Outputs: VH = 2.5V(min.), VL = 0.6V(max.)
[NETWORK] Connector (100Base-TX Ethernet, RJ-45)
Pin
Connection
1
TxD+
2
TxD–
3
RxD+
4
Unused
Unused
RxD–
5
6
7
Unused
Unused
8
Straight and Crossover Cable Wiring
Straight Cables
Crossover Cables
Pins
Pins
1 –– 1
1 –– 3
2 –– 2
2 –– 6
3 –– 3
3 –– 1
4 –– 4
4 –– 4
5 –– 5
5 –– 5
6 –– 6
6 –– 2
7 –– 7
7 –– 7
8 –– 8
8 –– 8
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
47
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
Dimensions
1
440
480
Rubber feet
are included in
the package.
44
Unit: mm
* Specifications and descriptions in this owner’s manual are for information purpose only. Yamaha Corp. reserves the right to
charge or modify products or specifications at any time without prior notice. Since specifications, equipment or options may
not be the same in every locale, please check with your Yamaha dealer.
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 35A
Conforms to Environments: E1,E2,E3 and E4.
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
48
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
Index
A
I
[AC IN] Connector ................................................................. 20
B
C
L
M
D
N
O
[OUTPUT] Connectors ..........................................................21
E
P
F
G
R
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
49
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
References
S
T
U
W
Z
DME8i-C/DME8o-C/DME4io-C Owner’s Manual
50
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
Para detalles sobre productos, contacte su tiendaYamaha más cercana
o el distribuidor autorizado que se lista debajo.
POLAND
Yamaha Music Central Europe GmbH
Sp.z. o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: 022-868-07-57
NORTH AMERICA
ASIA
CANADA
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
25/F., United Plaza, 1468 Nanjing Road (West),
Jingan, Shanghai, China
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
THE NETHERLANDS/
Tel: 021-6247-2211
BELGIUM/LUXEMBOURG
U.S.A.
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
Yamaha Music Central Europe GmbH,
Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
FRANCE
Yamaha Musique France
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
KOREA
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: 55-5804-0600
Yamaha Music Korea Ltd.
8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,
Kangnam-Gu, Seoul, Korea
Tel: 080-004-0022
ITALY
Yamaha Musica Italia S.P.A.
Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-78030900
BRAZIL
SPAIN/PORTUGAL
Yamaha Musical do Brasil Ltda.
Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,
CEP 04534-013 Sao Paulo, SP. BRAZIL
Tel: 011-3704-1377
Yamaha Música Ibérica, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-639-8888
SINGAPORE
Yamaha Music Asia Pte., Ltd.
#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: 747-4374
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Olga Cossettini 1553, Piso 4 Norte
Madero Este-C1107CEK
Buenos Aires, Argentina
SWEDEN
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1, Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
TAIWAN
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: 011-4119-7000
DENMARK
YS Copenhagen Liaison Office
Generatorvej 6A, DK-2730 Herlev, Denmark
Tel: 44 92 49 00
Tel: 02-2511-8688
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
THAILAND
Siam Music Yamaha Co., Ltd.
891/1 Siam Motors Building, 15-16 floor
Rama 1 road, Wangmai, Pathumwan
Bangkok 10330, Thailand
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1, N-1345 Østerås, Norway
Tel: 67 16 77 70
Tel: 02-215-2626
Tel: +507-269-5311
OTHER ASIAN COUNTRIES
RUSSIA
Yamaha Corporation,
Yamaha Music (Russia)
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
Office 4015, entrance 2, 21/5 Kuznetskii
Most street, Moscow, 107996, Russia
Tel: 495 626 0660
EUROPE
THE UNITED KINGDOM
Yamaha Music U.K. Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: +81-53-460-2317
OTHER EUROPEAN COUNTRIES
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
OCEANIA
Tel: 01908-366700
AUSTRALIA
GERMANY
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
AFRICA
Yamaha Corporation,
Tel: 3-9693-5111
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Central Europe GmbH,
Branch Switzerland
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Tel: +81-53-460-2313
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Naka-ku, Hamamatsu,
Japan 430-8650
MIDDLE EAST
AUSTRIA
Yamaha Music Central Europe GmbH,
Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
Tel: +81-53-460-2313
TURKEY/CYPRUS
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA
Yamaha Music Central Europe GmbH,
Branch Austria, CEE Department
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
OTHER COUNTRIES
Yamaha Music Gulf FZE
LOB 16-513, P.O.Box 17328, Jubel Ali,
Dubai, United Arab Emirates
Tel: +971-4-881-5868
HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Instruments de musique Division
Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2441
PA20
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
Yamaha Pro Audio global web site:
Yamaha Manual Library
U.R.G., Pro Audio & Digital Instruments de musique Division, Yamaha Corporation
© 2006 Yamaha Corporation
WK83890 804IPDHx.x-02D0
Printed in Japan
This document is printed on chlorine free (ECF) paper with soy ink.
Télécharger from Www.Somanuals.com. All Manuals Search And Télécharger.
|